Teach you how to drive multiple strings of LEDs with a single current loop

It is well known that LEDs are preferably driven by a constant current source. For LED applications that require less current, the linear drive scheme works well. However, when the LED requires more current, the switching power supply design is required. If there is only one LED string in the application, the control is straightforward. But if there are multiple strings of LEDs, the control becomes complicated. For example, one factor to consider is what to do if a string of LEDs in a multi-string LED is open. If current mode control is used, then in general, the current of the string of LEDs that are originally flowing through the open circuit is now forced to shunt into the remaining LED strings, increasing the current of these LED strings and shortening their lifetime. This situation is not a good thing. This design note describes a method for automatically detecting LED string open and adjusting accordingly.

Central issue:

* Automatically detect LED string open circuit and adjust accordingly

solution:

* Add a sense resistor to the bottom of each string of LEDs, using only one control loop

* PNP and NPN transistors for open-circuit LED strings are automatically turned off, and the feedback voltage of the LEDs is removed from the loop

When a switching regulator is normally used in constant current mode, a small sense resistor at the bottom of the LED string measures the current, and then the voltage of the sense resistor is fed back to the regulator's control loop. But if there are multiple strings of LEDs, how do designers control the loop? Some designers use a sense resistor at the bottom of all LED strings, but this creates the aforementioned LED string open problem. Other designers have Zener clamps for each LED. This method is certainly effective but costly because each LED requires a Zener device. There are also designers who use separate switching regulators and control loops for each string of LEDs, which also makes the cost prohibitive.

Instead of using multiple control loops for each string of LEDs, we can add only one control loop by adding a sense resistor to the bottom of each string of LEDs. Then, some PNP transistors are added to the sense resistors, and the collectors of these PNP transistors are connected together and transmitted to the control loop. A separate NPN transistor is also added in series with the base of the PNP transistor to open the current path when the PNP transistor is in reverse bias. This reverse biasing occurs when the LED string is open; when the feedback voltage is applied to the collector of the PNP transistor, the emitter junction is pulled to ground (Figure 1).

Figure 1, block diagram of NCP3063

SMT PCB Assembly =  SMT Printed Circuit Board Assembly, which means the PCB Board only have SMT parts need be assembled. Zhongfeng would manufacture the rigid PCB boards follow the design file, source the components follow the BOM file and do the PCB Assembly job follow the assembly drawing and the pick&place file. After PCB assembly done, the components would be mounted on the PCB boards tightly and connected each other through the copper circuits. We call such board as PCBA board or SMT PCBA board.

 

Depends on the components assembly types, it have THT PCB assembly, SMT PCB assembly, one sided SMT and THT PCB assembly, two sided SMT and THT PCB assembly.

 

Depends on the PCB type, it have Rigid PCB Assembly, Flex PCB Assembly and Flex-Rigid PCB Assembly.

 

Also we would call some PCB assembly types as Prototype PCB Assembly, Mass PCB Assembly , Turnkey PCB Assembly, LED PCB Assembly and BGA PCB Assembly , etc.

 

With our 15years professional experience, we are available for all types of PCB assembly service from prototype to mass production, available for 01005, 0201, 0.3mm BGA, 0.3mm QFP.


PCB Assembly Capabilities

Quantity

1 pcs - 1,000,000 pcs

Assembly type

SMT, THT or Hybrid

Parts procurement

Full turnkey (ZhongFeng provide all components)

Partial turnkey ( Customer provide the main components and ZhongFeng provide the rest)

Kitted (Customer provide all components)

Component types

SMT 01005, 0201, BGA 0.3mm pitch, QFP 0.3mm pitch, etc.

Test

Visual Inspection, AOI, Custom testing, ICT, FCT, Test jig




PCB Assembly Products Show


PCB Assembly Boards


PCB SMT Assembly Factory Show


ZhongFeng SMT Factory


ZhongFeng SMT Factory

SMT PCB Assembly

SMT PCB Assembly,Surface Mount SMT PCB Assembly, Professional SMT PCB Assembly,Electronic SMT PCB Assembly

ZhongFeng Electronic Technology Co., Limited , http://www.dopcba.com