Xiao Bian Note: Double 11 to buy half of the sun lost, # # Sun single contest hot strikes, smashed hands have opened a box! IPhoneX etiquette waiting for you to win, submissions that get extra 100 gold coins, as well as original innovators exclusive rewards, App can light submission, details poke here.
Mobile phone stickers are always a topic that can't go around. The current mobile phone screen is getting larger and the screen is getting closer and closer to the frame. This makes the screen easily broken.
Since 2002, the PDA has been used since the beginning of the film. The early film was just to prevent the touch screen from being worn under long-term operation. Subsequent cell phone stickers were also designed to prevent scratches on the screen, but these PVC soft films did not protect the screen from falling. The current tempered film has this function. The mobile phone with a tempered film attached has a much smaller chance of cracking on the screen. Usually, tempered film replaces screen fragmentation and energy absorption.
However, the 2.5D glass used in the iPhone 6 brings a tough challenge to the tempered film. The normal tempered film that cannot be covered by a full screen is like a crack, and it appears to be particularly obtrusive on the screen of a mobile phone. Later, there was a soft-edged tempered membrane, but as an obsessive-compulsive disorder patient couldn't tolerate the poor consistency of the entire screen, and there was always a trace of the stitched place. Therefore, ordinary non-full-screen toughened films have been used.
Until one day you see a full screen integrated tempered film. There is no splicing between hard and soft sides, and the entire front is a one-piece glass, just like the screen of a mobile phone itself. This I can accept. So at the friend recommended in the RAV this film.
Unpacking & Foil:
Steel film commonly used hard box packaging, to avoid the damage caused by transport squeeze.
There are also carton sleeves inside.
Expand all content is a film body, a back film, a set of dust cleaning kit
This is the original film of the mobile phone, non-full-screen film is not good this point, not full-screen protection.
The full-screen film is whiter than the regular film. Just like the entire front panel of the phone.
The edge of the full-screen film on the soft edge was covered with a rubber material, and the tempered film was not the same as the edge. Whether it is a visual or tactile experience is poor.
I would like to give it a try after the current full-screen screen tempered glass film matures.
The ordinary steel film stick 2.5D glass paste is not complete, the edge is easy to filth, which is what I want to solve.
Remove the old tempered film and prepare to start work.
Remove the wet wipes package first.
Walk along the traces of the old foil and wipe away dirt and grease.
Then open the paper towel pack and wipe off the water from the wipes.
Separated from the film and film protection layer.
The first time the hard-edged full-screen glass film was attached, RAV's protective layer of this film is a whole piece of hard plastic film that made me feel more accidental. But if you think about it, you can think why. Watching the film structure is that the middle transparent part completely fits the screen and is electrostatically bonded like a normal film. Then the edge is curved and fits on the edge of the phone, but it is not glued. Such special-shaped film can only be transported with hard plastic to protect it and avoid damage.
Soft-edge film on the transparent plastic film with PVC to protect the transparent part of the film only. Foil detail is slightly worse.
Wipe the ash on the screen ready to cover the film
I was first aligned with the hole above
Then align the fingerprint and put it down
Look at the transparent part of the center of the screen. The film is also nearing completion.
It's good to use a dry rag to squeeze out the big bubbles.
It does not matter if the small bubbles under the tempered film cannot be squeezed out. It will disappear in a few days.
Foil fit:
The location of the opening of the film is better. Of course, to achieve this price, it is certainly not necessary to do this work.
Foil edge fit is also better.
If you do not look carefully, it is difficult to find that a layer of tempered film has been applied.
Summary & Usage Experience:
Placing a tempered film is not so difficult. Small particles of dust hardly form bubbles under the pressure of the tempered film. The biggest difficulty with RAV's full-screen tempered film is that it is aligned with the hole and does not require much lamination. Positive integration of full-screen film than the use of soft-sided film splicing process is much better than the perception, especially to cure obsessive-compulsive disorder.
From the edge of the film after the degree of fit to see this film die precision is relatively high. I know that many of my friends will pay for the cost, but as a worker, I want to say that the value of many things is not worthwhile. To really take the material cost to do things, a i9-7900 processor with silicon, plastic, steel shell value of 100 yuan it? Pull away...
The surface of the film is smooth and it is not easy to leave fingerprints. The touch is like the body painted with powder, the feel is closer to the screen's original feel. Compared with the past, the dry feel of the film has greatly improved. In my opinion, it is about 2 times the smoothness of ordinary tempered film, and it is better than PVC soft film to know where to go. The smooth feel of the tempered film is also a big reason why I didn't use a PVC film after I used it.
The quality of RAV's tempered film is beyond my expectations, but there are also minor issues.
The film itself has a certain thickness, which is a bit thicker than the 0.2 ultra-thin tempered film I originally used, so the Home button is also slightly deeper. It feels similar to 0.3 tempered film.
If you do not mind this, then the quality of this film is still very satisfied with me. After adding the tempered film, besides the home button, the same look and feel as the original screen is my favorite point.
I-Beam Inductors,Chip Inductors,Color Ring Inductor,R-Bar Inductors
Shenzhen Sichuangge Magneto-electric Co. , Ltd , https://www.scginductor.com